Easily Fix A Kinked AC Line Set, Just 1 Idea
This method to repair a kinked AC line set should be made when the line set is not under pressure.
If this kink is connected to an HVAC system that is charged with refrigerant, pump down the system or remove refrigerant for safety.
First, determine how severe the kink is so you can decide whether you should repair it or leave it alone. This next image shows a mildly kinked AC line set that you could easily repair or leave alone because it’s not too restrictive to the flow of refrigerant.
On the other hand, this next image shows a kinked AC line set that needs attention. I’ll show you how to repair this kink using a very basic tool that almost anyone has or can borrow that can return that pipe nearly back to normal.
This is an affiliate site. Links will lead you to another site and connect you with products that support this article.
This kink is near the range of 50% restriction. With this type of kink in a refrigeration line you can be losing efficiency, raising and lowering pressures and shortening the life of your mini split or AC system.
I’ve seen some repair jobs and YouTube videos showing how to make these kinks go away and I wasn’t too impressed. They were using channel locks which have teeth in the jaws and caused excessive scaring and potentially creating leaks in the copper line.
My favorite tool to repair a kinked AC line set is a plain old ordinary 12″Adjustable Wrench.
Set the jaws of the Crescent wrench to the diameter of the pipe by placing the wrench over a good (round) section of the pipe and adjusting the wrench until it’s not quite tight but slightly loose.
Begin moving the wrench back and forth around the pipe working gently towards the kink. If possible put some pressure on the pipe to physically straighten kink while working the kink out with the wrench. It is possible to make the kink worse by being too aggressive. Take your time and work it out slowly.
Work at it from both sides or ends of the kink. If you can find a scrap piece of copper to practice on it would be very beneficial.
Continue rounding the pipe while appling pressure on the pipe to straighten until you feel it’s no use to keep going. Your finished kink repair should look something like the image below with very little restriction to the flow of refrigerant.
Will A Kinked AC Line Set Leak?
Warning: be aware of using this method to repair a kink when your copper line set is charged and under pressure it is possible with severe kinks to create a leak.
It’s easy to spot a repair turning into a possible leak. The downside of creating a leak is the need to make a more intensive repair using an oxygen and acetylene welding set. You would have to cut the line and with the use of a swaging tool or a coupling and then weld the copper together.
Incidentally that swaging tool link is on Amazon and it’s a tool that I really like using. It will swag a variety of sizes and is easy to use. It beats the single swaging tools the you have to use a clamp and a hammer to form the swag.
It’s also a little more complicated than that. The lines need to be purged with nitrogen during the welding process to prevent carbon from forming in the lines. Carbon inside a line set will prematurely end the life a mini split that contains R-410A, the new atmosphere friendly refrigerant or Freon as most people know it by.
How Much Should It Cost To Repair A Kinked AC Line Set?
Refrigeration line sets can get kinked for various reasons. While trying to install a line set around tight corners or even during shipping. With the price and availability of copper these days, knowing how to make a good repair will save a few bucks and some time.
The image below shows a couple of fairly severe kinks (ad). This line set was installed when the house was built under the premise that the house would be “AC ready”.
An AC ready home has a few things like heating and cooling thermostat, line set, and power wiring with outside disconnect already installed which makes the new install of an air conditioner a lot easier. So this line set just stuck outside of the house for several years and someone inadvertently (or purposely) went up and bent it.
So using this kinked AC line set line repair scenario you have to realize that this line set was not charged or under pressure so the time involved to fix the kink was less than if it had been under pressure. If it had been under pressure I would have had to pump out the refrigerant, purge with nitrogen, make the weld, evacuate, recharge with Freon. In other words, a lot more labor costs.
This repair had been kinked up inside the wall. Lucky I noticed that, right! Had to cut the wall open to access the kink to a point to where I could weld the joint without burning the house down. After welding in the outdoor unit I was able to trim the hole with sheet metal a locate a really close color match with some spray paint the made a nice finish.
